Dji Z15-GH4 (HD Bedienungsanleitung PDF herunterladen (Seite 15)

GCU Wiring

WooKong-M users can connect the GCU to any spare CAN-Bus port on the ight control system by using a CAN-

Bus cable.

A2 users should connect the GCU to the port labeled CAN1. Alternatively, you may connect the GCU to

the CAN port located on any modules that are already connected to the A2’s CAN1 port via a CAN-Bus cable.

GCU Wiring

A2/WooKong-M

Please refer to your A2/WooKong-M User Manual for all connection and conguration details.

Gimbal Control Unit (GCU)

1. Make sure all ports are accessible when installing your MC so as to facilitate wiring and software conguration.

2. In 3-pin ports, the pins near the nicks are the signal pins.

3. Use the 6-pin cable for the G6 port, and the 10-pin to 9-pin cable for the G9 port.

4. DO NOT cover the heat sinks, and keep them unobstructed at all times.

5. The IMU module is NOT waterproof or oil proof.

RC Receiver

1. The diagram on the previous page shows example connections. The aircraft signal will transmit through the DJI

Lightbridge ground system. After connecting to the Lightbridge, it is not necessary to connect with the RC receiver.

2. Prepare 2 TXs, one for gimbal control, and the other for aircraft control. Refer to the 2-Pilots Solution for more detail.

3. If only one receiver is used for both aircraft and gimbal control, refer to the 1-Pilot Solution for more detail.

4. Setup the Aileron, Elevator, and Rudder channels on the gimbal control TX. The command stick will control

gimbal rotation velocity. The center position is 0, and the end point is maximum velocity in both clockwise

and counter clockwise directions. (The end point is 100%)

5. Choose one 3-position switch/channel to use as the Z15-GH4 Working Mode switch. (MODE)

6. Choose one 2-position switch/channel to use as the camera shutter control switch (SHUT), and another

2-position switch to use as the camera lens orientation switch in Reset Mode (AUX2).

7. Please refer to the A2/Wookong-M User Manual for aircraft control settings. Connect the receiver to the GCU correctly.

Turn to next page to obtain the

correspondence between the GCU

channels and S-Bus/PPM channels.

Battery

Connect the XT60 to the GIMBAL on center frame if S800 EVO used.

Attention that S800 EVO power supply voltage should be within the defined limits (6S), when

using one battery for both S800 EVO and Gimbal power supply.

Refer to S800 EVO User Manual for details.

ROLL

TILT

PAN

MODE

SHUT

AUX1

AUX2

AUX3

A2/WKM

•

S-Bus

PPM

2-Position Switch

3-Position Switch

2-Position Switch

3-Position Switch

2-Position Switch

USB Port

PC connection for configuration and

firmware upgrades with an USB cable.

Ensure the side with copper contacts is

facing upward towards the heat sinks.

RC Receiver

(Aircraft control)

Battery

(4S~12S)

Wireless Video

Transition Module

Air Unit

RC Receiver

（JR）

8 Channels

RC Receiver

(Futaba/Hitec)

8 Channels

S-BUS Receiver

(Futaba)

PPM Receiver

GH4 HD

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare

Dji Z15-GH4 (HD Bedienungsanleitung Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Dji Z15-GH4 (HD